In a previous post, I wrote about a Disston panel saw that I bought at a garage sale. In the little time that I have spent in my shop over the last month, I have not spent much time working on the workbench that I am building, but have restored a Union No. 41 plane, a Dunlap draw knife, and now this panel saw. But this is it… No really, I swear… I will return to building my workbench. After all, what good is this huge collection of hand tools I’m growing, if I don’t have a workbench to use them on?
Here is the saw that I bought:
The saw is a 20″ panel saw, it has 10 points per inch (PPI), and is filed cross-cut.
There was some rust and lots of grime on the saw plate. However, the rust appeared to be on the surface only and I didn’t think that pitting would be an issue. The tote was a different story. The original factory lacquer had turned yellow and was crumbling off. I realized that a complete refinishing would be needed here.
I disassembled the saw and started by cleaning the saw plate. I used a razor-blade scraper to remove the surface rust, being careful not to let the corners dig in and scratch the saw. I then used a sanding block with 220 grit paper to further clean the plate. I wet sand when I do this, but I use oil not water. As you sand the oil turns dark and nasty, but it is easy to periodically wipe this up with some paper towels. Be careful not to put these in the trash can though, they might combust. I know its not likely with household lubricating oil, but why chance it? I put mine in the wood stove.
I should also point out the importance of using a sanding block for this task. By evenly distributing the pressure, the sanding block helps to protect any etching that may remain on the saw plate. If you just use your fingers directly on the paper, the pressure is more likely to sand the etch away.
The saw plate cleaned up quite nicely and the original etch revealed that the saw was a Disston D-8.
I turned to the web to find out a little more about this saw and try to date it.
The best place to go online for information on Disston saws that I have found is The Disstonian Institute. The site contains more info about these saws than you would have thought possible.
I searched for some information on the etch that was revealed by cleaning the saw plate. According to this page, the etch dates the saw to after 1928.
I took the saw nuts and the medallion and cleaned them up at the buffer. All of the other handsaws that I have ever restored have had brass hardware, This saw has steel hardware and it may have been nickel plated. As you can see below, the hardware cleaned up nicely and the formerly crud filled medallion can now be read easily.
I looked on another Disstonian Institute page and was able to date the medallion. It appears that the saw was made and sold sometime between 1947 and 1955.
With the saw plate cleaned, It was time to sharpen it. Last year I spent considerable time learning to sharpen saws and wrote about it at the time. I use a set of files and file holders that I bought from a Lee Valley store when I took a trip to Vancouver, BC. By the way… wives love it when you are supposed to be taking them on holiday to do a little sightseeing and as part of your vacation, take them to a Lee Valley store. It goes over real well, you should try it!
I jointed the saw, filed the teeth, set the teeth, lightly re-jointed the teeth and filed them one last time to remove any small remaining flat spots. I won’t go into too much depth here on saw sharpening, as I already did that in a series of earlier posts in which I restored a I. Sorby Tenon Saw. You can click the link to see and in depth explanation of my saw sharpening process.
I left the saw at 10 PPI and filed it with 10° of rake and 15° of fleam. Below you can see I have made the first pass filing only every other tooth.
Once the saw plate was cleaned a sharpened, I sprayed it with a coat of Bostik Top Coat to help prevent future rust or corrosion.
With the saw plate sharpened and cleaned and the hardware polished, it was time to move on to the tote. I find that this is always the most time consuming and tedious part of saw restorations. I started out with 100 or 120 grit paper and sanded away all of the old finish but didn’t sand into the bare wood too far or try to remove and deep scratches or staining. I think these add a little character to the saw and show the saw’s age. I then sanded the tote to 220 grit to prepare it for finish. All of this sanding took me a couple of hours.
Here are all the saw parts cleaned up. I just need to apply finish to the tote and put it all back together.
Again, I won’t go into too much detail here about how I re-finished the tote, as I did this in great depth in part 4 of my earlier Tenon saw restoration series. In brief, I apply about 4 coats of Watco Danish Oil. I like the red mahogany color. The first coat goes on very wet and heavy and is applied until the wood will soak up no more. After half an hour, I wipe of the excess and leave the tote to dry.
The red mahogany Danish Oil looks very red until you wipe of the excess, but then it leaves a beautiful color.
The second coat gets applied and sanded in with 320 grit paper. Again the excess finish is wiped off. The third and fourth coats are applied with 400 grit paper. This whole process is tedious, but I love the end result. It leaves a silky smooth finish without having a film on the wood that can get damaged or deteriorate. The finish is in the wood and if you ever need to touch up the tote, all you have to do is sand in a little more Danish Oil.
After the fourth coat is thoroughly dried (I think I waited 3 days), I apply a final coat of wax. This adds a nice sheen to the tote and I like the way it makes the tote feel in the hand. To me it seems a little “grippy-er”. Since I had the can of wax out, I also took the time to put a coat of wax on the saw plate.
I love this method of refinishing saw totes. As you can see, the tote does not look brand new. It feels new, it’s clean and dirt/grime free, but it still has the marks of age. Some of the deeper dings and dents can be seen and and there is still some staining visible.
With all the components restored, I reassembled the saw.
Next, I got carried away with the camera and took a load of pictures.
You think that the Schwarz would like the clocked saw nuts?
Now… back to that workbench that I’m supposed to be building (instead of using it as a photo prop).