This is the third post in a series covering the installation of the dust collection system for my workshop. The previous posts can be found here:
- Dust Collector Project – Part 1 (mounting the dust collector on the wall)
- Dust Collector Project – Part 2 (installing a shop made wireless remote system)
In this part of the series, I design and build a bunch of brackets to hang 4″ PVC pipe from the ceiling of my workshop. I decided to use PVC pipe for my ducting as metal ducting is very expensive. Ideally, I would have liked to use 6″ PVC pipe for the main branch of the duct and step down to 4″ at the branches that lead off to each tool. The additional cost of the pipe is not too bad, it’s about $2/ft versus $1/ft. However, the cost of the fittings (elbows, “Y”s, 45s, etc.) is about 4-5 times as much for 6″ as for 4”. For example, a 4″ Y cost me about $5.50, whereas a 6″ Y was going to cost $23.00.
I realistically need no more than 500 CFM (350 would probably be sufficient) at any of my tools and my dust collector is rated at 1,700 CFM. I figured that even if I built a very inefficient ducting system, I wouldn’t reduce its CFM to such an extent that it would be below needed levels at the tool. I recognize that the 1,700 CFM rating of my collector is probably obtained with no filter attached and a wide open intake port, and that this number will drop drastically once connected to a spiderweb of 4″ pipe. The ratings that the companies give their collectors is not standardized and can be a little deceptive. The system that I’m installing likely has more joints, fitting, and angle changes than the “experts” would recommend, but I still think that my 2hp collector will have sufficient power to extract the dust as needed. Let’s hope I don’t have to eat those words later.
As with just about any project, I turned to the internet in search of plans, ideas, or at least inspiration for a good pipe hanging bracket. The only things that I found were either U-shaped metal brackets or flexible metal strapping with holes every inch or so. Neither of these appealed to me. If I have to make any changes or want to make additions to the ducting later, I don’t want to have to remove all those straps. I’d rather have a system the cradles the pipe and allows for easy removal or adjustment. I decided that I would have to design something of my own. My sheet good storage bin has quite a few odd pieces of plywood, so I thought it would be a good opportunity to use up as much of this material as needed.
I cut off a small piece of pipe and traced around it on paper. This became the start of my hanger/bracket profile. I designed the bracket so that the pipe can lifted up and out of the bracket from the front without having to unfasten anything or slide the pipe out the side. Here’s what my sketch ended up looking like:
The dimensions that I decided upon were 6″ x 8½”. I found several pieces of ½” baltic birch plywood that I had left over from previous projects and cut them to size. I taped these blanks together in stacks of four. with some blue painters tape.
I then used the sketch as a template and traced the pattern onto all the stacks.
Sorry for the crappy photo below, I must have focused on the wrong spot.
This should keep me in brackets for a while.
To make the ½” brackets a little more rigid, I designed them to be used in pairs. Between them, they have a top, bottom, and back all cut from ¾” ply found in my storage rack. I cut these spacer pieces about 2¾” wide, which I figured was the minimum width that I could use and still have room for pocket screws.
I drilled pocket holes in all the top and bottom spacers. The backs will be held in place with glue and pin nails.
I kept assembling parts until all the brackets were put together.
The edges needed to be smoothed and rounded over at the combination sander.
Then came the not so fun part. It took way longer to paint these things than it did to make them.
I cut up some more ½” ply into 6″ x 8″ rectangles and rounded over the edges of one side with the palm router. After a little sanding, these too got a coat of paint and were set aside to dry.
When everything was dry, I attached the base plates to the bracket assemblies, screwing down from the top. The now complete brackets all got a second coat of paint. Did I mention that this painting lark takes forever!!!
Installation of the brackets couldn’t be simpler. A washer head screw is used and goes through the base plate and into the ceiling joist. The screws can be used in any location on the base plate, which means that you can rotate the bracket to whatever angle or direction is needed and screw through into the joist. The screws could be on the front and back, the sides, or even diagonal. It doesn’t matter as long as they go into the joist and not just sheet rock.
I built 11 of these brackets, which is probably more than I need to install the system as it stands. I figured that having a few left over wouldn’t be a bad thing and would give me the ability to add-on to the ducting later without having to repeat this whole process. I like the clean look and despite it taking ages, I’m glad that I took the time to paint the brackets. White pipe, white ceiling, white brackets. I haven’t had to buy any wood at any stage of this project and I’m glad to be finding a good use for all the scrap pieces I’d saved.
In the next post, I’ll show you the special brackets that I had to come up with to cantilever a 8-foot section of pipe under the roll up garage door.
– Jonathan White